Section 64.55.010 - [Effective Until 1/1/2028] DefinitionsUnless the context clearly requires otherwise, the definitions in *RCW 64.34.020 and in this section apply throughout this chapter.
(1) "Attached dwelling unit" means any dwelling unit that is attached to another dwelling unit by a wall, floor, or ceiling that separates heated living spaces. A garage is not a heated living space.(2) "Building enclosure" means that part of any building, above or below grade, that physically separates the outside or exterior environment from interior environments and which weatherproofs, waterproofs, or otherwise protects the building or its components from water or moisture intrusion. Interior environments consist of both heated and unheated enclosed spaces. The building enclosure includes, but is not limited to, that portion of roofs, walls, balcony support columns, decks, windows, doors, vents, and other penetrations through exterior walls, which waterproof, weatherproof, or otherwise protect the building or its components from water or moisture intrusion.(3) "Building enclosure design documents" means plans, details, and specifications for the building enclosure that have been stamped by a licensed engineer or architect. The building enclosure design documents shall include details and specifications that are appropriate for the building in the professional judgment of the architect or engineer who prepared the same to waterproof, weatherproof, and otherwise protect the building or its components from water or moisture intrusion, including details of flashing, intersections at roof, eaves or parapets, means of drainage, water-resistive membrane, and details around openings.(4) "Developer" means: (a) With respect to a condominium or a conversion condominium, the declarant; and(b) With respect to all other buildings, an individual, group of individuals, partnership, corporation, association, municipal corporation, state agency, or other entity or person that obtains a building permit for the construction or rehabilitative reconstruction of a multiunit residential building. If a permit is obtained by service providers such as architects, contractors, and consultants who obtain permits for others as part of services rendered for a fee, the person for whom the permit is obtained shall be the developer, not the service provider.(5) "Dwelling unit" has the meaning given to that phrase or similar phrases in the ordinances of the jurisdiction issuing the permit for construction of the building enclosure but if such ordinances do not provide a definition, then "dwelling unit" means a residence containing living, cooking, sleeping, and sanitary facilities.(6) "Multiunit residential building" means: (a) A building containing more than two attached dwelling units, including a building containing nonresidential units if the building also contains more than two attached dwelling units, but excluding the following classes of buildings: (v) A building that contains attached dwelling units that are each located on a single platted lot, except as provided in (b) of this subsection;(vi) A building in which all of the dwelling units are held under one ownership and is subject to a recorded irrevocable sale prohibition covenant;(vii) A building with 12 or fewer units that is no more than two stories; and(viii) A building with 12 or fewer units that is no more than three stories so long as one story is utilized for parking, either above or below ground, or retail space.(b) If the developer submits to the appropriate building department when applying for the building permit described in RCW 64.55.020 a statement that the developer elects to treat the improvement for which a permit is sought as a multiunit residential building for all purposes under this chapter, then "multiunit residential building" also means the following buildings for which such election has been made: (i) A building containing only two attached dwelling units;(ii) A building that does not contain attached dwelling units; and(iii) Any building that contains attached dwelling units each of which is located on a single platted lot.(7) "Party unit owner" means a unit owner who is a named party to an action subject to this chapter and does not include any unit owners whose involvement with the action stems solely from their membership in the association.(8) "Qualified building inspector" means a person satisfying the requirements of RCW 64.55.040.(9) "Rehabilitative construction" means construction work on the building enclosure of a multiunit residential building if the cost of such construction work is more than five percent of the assessed value of the building.(10) "Sale prohibition covenant" means a recorded covenant that prohibits the sale or other disposition of individual dwelling units as or as part of a condominium for five years or more from the date of first occupancy except as otherwise provided in RCW 64.55.090, a certified copy of which the developer shall submit to the appropriate building department; provided such covenant shall not apply to sales or dispositions listed in *RCW 64.34.400(2). The covenant must be recorded in the county in which the building is located and must be in substantially the following form: This covenant has been recorded in the real property records of . . . . . . County, Washington, in satisfaction of the requirements of RCW 64.55.010 through 64.55.090. The undersigned is the owner of the property described on Exhibit A (the "Property"). Until termination of this covenant, no dwelling unit in or on the Property may be sold as a condominium unit except for sales listed in *RCW 64.34.400(2).
This covenant terminates on the earlier of either:
(a) Compliance with the requirements of RCW 64.55.090, as certified by the owner of the Property in a recorded supplement hereto; or(b) the fifth anniversary of the date of first occupancy of a dwelling unit as certified by the Owner in a recorded supplement hereto.All title insurance companies and persons acquiring an interest in the Property may rely on the forgoing certifications without further inquiry in issuing any policy of title insurance or in acquiring an interest in the Property.
(11) "Stamped" means bearing the stamp and signature of the responsible licensed architect or engineer on the title page, and on every sheet of the documents, drawings, or specifications, including modifications to the documents, drawings, and specifications that become part of change orders or addenda to alter those documents, drawings, or specifications.Amended by 2024 c 122,§ 1, eff. 6/6/2024.Amended by 2023 c 263,§ 1, eff. 7/23/2023.*Reviser's note:RCW 64.34.020 and 64.34.400 were repealed by 2024 c 321 s 502, effective January 1, 2028.
This section is set out more than once due to postponed, multiple, or conflicting amendments.