Iowa Code § 105.2

Current through March 29, 2024

Section 105.2 - Definitions

As used in this chapter, unless the context otherwise requires:

1."Apprentice" means any person, other than a helper, journeyperson, or master, who, as a principal occupation, is engaged in working as an employee of a plumbing, mechanical, HVAC-refrigeration, sheet metal, or hydronic systems contractor under the supervision of either a master or a journeyperson and is progressing toward completion of an apprenticeship training program registered by the office of apprenticeship of the United States department of labor while learning and assisting in the design, installation, and repair of plumbing, HVAC, refrigeration, sheet metal, or hydronic systems, as applicable.

2."Board" means the plumbing and mechanical systems board as established pursuant to section 105.3.

3."Contractor" means a person or entity that provides plumbing, mechanical, HVAC, refrigeration, sheet metal, or hydronic systems services on a contractual basis and who is paid a predetermined amount under that contract for rendering those services.

4."Department" means the department of inspections, appeals, and licensing.

5."Governmental subdivision" means any city, county, or combination thereof.

6."Helper" means a person engaged in general manual labor activities who provides assistance to an apprentice, journeyperson, or master while under the supervision of a journeyperson or master.

7."HVAC" means heating, ventilation, air conditioning, ducted systems, or any type of refrigeration used for food processing or preservation. "HVAC" includes all natural, propane, liquid propane, or other gas lines associated with any component of an HVAC system.

8."Hydronic" means a heating or cooling system that transfers heating or cooling by circulating fluid through a closed system, including boilers, pressure vessels, refrigeration equipment in connection with chilled water systems, all steam piping, hot or chilled water piping together with all control devices and accessories, installed as part of, or in connection with, any heating or cooling system or appliance whose primary purpose is to provide comfort using a liquid, water, or steam as the heating or cooling media. "Hydronic" includes all low-pressure and high-pressure systems and all natural, propane, liquid propane, or other gas lines associated with any component of a hydronic system. For purposes of this definition, "primary purpose is to provide comfort" means a system or appliance in which at least fifty-one percent of the capacity generated by its operation, on an annual average, is dedicated to comfort heating or cooling.

9."Journeyperson" means any person, other than a master, who, as a principal occupation, is engaged as an employee of, or otherwise working under the direction of, a master in the design, installation, and repair of plumbing, mechanical, HVAC, refrigeration, sheet metal, or hydronic systems, as applicable.

10."Master" means any person who works in the planning or superintending of the design, installation, or repair of plumbing, mechanical, HVAC, refrigeration, sheet metal, or hydronic systems and is otherwise lawfully qualified to conduct the business of plumbing, mechanical, HVAC, refrigeration, sheet metal, or hydronic systems, and who is familiar with the laws and rules governing the same.

11."Mechanical professional" means a person engaged in the HVAC, refrigeration, sheet metal, or hydronic industry.

12."Mechanical systems" means HVAC, refrigeration, sheet metal, and hydronic systems.

13."Medical gas piping" means a permanent fixed piping system in a health care facility which is used to convey oxygen, nitrous oxide, nitrogen, carbon dioxide, helium, medical air, and mixtures of these gases from its source to the point of use and includes the fixed piping associated with a medical, surgical, or gas scavenging vacuum system, as well as a bedside suction system.

14."Medical gas system installer" means any person who installs or repairs medical gas piping, components, and vacuum systems, including brazers, who has been issued a valid certification from the national inspection testing certification (NITC) corporation, or an equivalent authority approved by the board.

15."Plumbing" means all potable water building supply and distribution pipes, all plumbing fixtures and traps, all drainage and vent pipes, and all building drains and building sewers, storm sewers, and storm drains, including their respective joints and connections, devices, receptors, and appurtenances within the property lines of the premises, and including the connection to sanitary sewer, storm sewer, and domestic water mains. "Plumbing" includes potable water piping, potable water treating or using equipment, medical gas piping systems, fuel gas piping, water heaters and vents, including all natural, propane, liquid propane, or other gas lines associated with any component of a plumbing system.

16."Refrigeration" means any system of refrigeration regardless of the level of power, if such refrigeration is intended to be used for the purpose of food processing and product preservation and is also intended to be used for comfort systems. "Refrigeration" includes all natural, propane, liquid propane, or other gas lines associated with any component of refrigeration.

17."Routine maintenance" means the maintenance, repair, or replacement of existing fixtures or parts of plumbing, mechanical, HVAC, refrigeration, sheet metal, or hydronic systems in which no changes in original design are made. Fixtures or parts do not include smoke and fire dampers, or water, gas, or steam piping permanent repairs except for traps or strainers. "Routine maintenance" shall include emergency repairs, and the board shall define the term "emergency repairs" to include the repair of water pipes to prevent imminent damage to property. "Routine maintenance" does not include the replacement of furnaces, boilers, cooling appliances, or water heaters more than one hundred gallons in size.

18."Sheet metal" means heating, ventilation, air conditioning, pollution control, fume hood systems and related ducted systems or installation of equipment associated with any component of a sheet metal system. "Sheet metal" excludes refrigeration and electrical lines and all natural gas, propane, liquid propane, or other gas lines associated with any component of a sheet metal system.

Iowa Code § 105.2

2007 Acts, ch 198, § 2; 2008 Acts, ch 1032, § 102, 202; 2008 Acts, ch 1089, §10, 11; 2009 Acts, ch 151, §2, 3; 2011 Acts, ch 100, § 1, 2, 15; 2012 Acts, ch 1023, § 22; 2012 Acts, ch 1026, §1, 2; 2012 Acts, ch 1138, § 47, 78, 79; 2013 Acts, ch 77, §2, 3, 36; 2023 Acts, ch 19, § 1572

Amended by 2023 Iowa, ch 19, s 1572, eff. 7/1/2023.

Amended by 2013 Iowa, ch 77, s 3, eff. 4/26/2013.

Amended by 2013 Iowa, ch 77, s 2, eff. 4/26/2013.

2007 Acts, ch 198, §2; 2008 Acts, ch 1032, §102, 202; 2008 Acts, ch 1089, §10, 11; 2009 Acts, ch 151, §2, 3; 2011 Acts, ch 100, §1, 2, 15; 2012 Acts, ch 1023, §22; 2012 Acts, ch 1026, §1, 2; 2012 Acts, ch 1138, §47, 78, 79

Referred to in §249K.5

Subsection 4 amended