Mich. Admin. Code R. 408.41590

Current through Vol. 24-21, December 1, 2024

Section R. 408.41590 - Helicopters; general requirements

Rule 1590.

(1) This rule applies to helicopters used during construction operations.

(2) Helicopter cranes must comply with any applicable regulations of the federal aviation administration.

(3) Prior to each day's operation a briefing shall be conducted by the pilot, ground crew, general contractor overseeing the work, and any sub-contractors involved. This briefing shall set forth the plan of operation for the pilot and ground personnel.

(4) A load shall be properly slung. Tag lines shall be of a length that will not permit the tag line being drawn up into rotors. Pressed sleeve, swedged eyes, or equivalent means shall be used for all freely suspended loads to prevent hand splices from spinning open or cable clamps from loosening.

(5) All electrically operated cargo hooks shall have the electrical activating device so designed and installed as to prevent inadvertent operation. In addition these cargo hooks shall be equipped with an emergency mechanical control for releasing the load. The hooks shall be tested prior to each day's operation by the helicopters employees, pilot, or mechanic, to determine that the release functions properly both electrically and mechanically.

(6) Personal protective equipment shall meet the following requirements:

(a) Personal protective equipment for employees receiving the load shall consist of complete eye protection and hard hats secured by chinstraps.

(b) An employee shall not wear loose-fitting clothing likely to flap in the downwash, and thus be snagged on hoist line.

(7) An employer shall ensure that every practical precaution is taken to provide for the protection of the employees from flying objects in the rotor downwash. All loose gear within 100 feet of the place of lifting the load, depositing the load, and all other areas susceptible to rotor downwash shall be secured or removed.

(8) An employer shall ensure that good housekeeping shall be maintained in all helicopter loading and unloading areas.

(9) The helicopter operator shall be responsible for size, weight, and manner in which loads are connected to the helicopter. If, for any reason, the helicopter operator believes the lift cannot be made safely, the lift shall not be made.

(10) When employees are required to perform work under hovering craft, a safe means of access shall be provided for employees to reach the hoist line hook and engage or disengage cargo slings. Employees shall not perform work under hovering craft except when necessary to hook or unhook loads.

(11) Static charge on the suspended load shall be dissipated with a grounding device before ground personnel touch the suspended load, or protective rubber gloves shall be worn by all ground personnel touching the suspended load.

(12) The weight of an external load shall not exceed the manufacturer's rating.

(13) Hoist wires or other gear, except for container or roll off a reel, shall not be attached to any fixed ground structure, or allowed to foul on any fixed structure.

(14) When visibility is reduced by dust or other conditions, ground personnel shall exercise special caution to keep clear of main and stabilizing rotors. An employer shall take precautions to eliminate as far as practical reduced visibility.

(15) Signal systems between aircrew and ground personnel shall be understood and checked in advance of hoisting the load. This requirement applies to either radio or hand signal systems. When using hand signals, either of the following methods shall be used:

(a) Standard helicopter hand signals as shown in Appendix B.

(b) Non-standard hand signals. When used, the signal person, operator, and lift director, when there is one, shall contact each other prior to the operation and agree on the non-standard hand signals that will be used.

(16) No unauthorized person shall be allowed to approach within 50 feet of the helicopter when the rotor blades are turning.

(17) Whenever approaching or leaving a helicopter with blades rotating, all employees shall remain in full view of the pilot and keep in a crouched position. Employees shall avoid the area from the cockpit or cabin rearward unless authorized by the helicopter operator to work in the area.

(18) An employer shall ensure that sufficient ground personnel are provided when required for safe helicopter loading and unloading operations.

(19) There shall be constant reliable communication between the pilot and a designated employee of the ground crew who acts as a signalman during the period of loading and unloading. This signalman shall be distinctly recognizable from other ground personnel.

(20) Open fires shall not be permitted in an area that could result in such fires being spread by the rotor downwash.

Mich. Admin. Code R. 408.41590

2016 MR 6, Eff. 3/22/2016