Ill. Admin. Code tit. 35 § 302.208

Current through Register Vol. 48, No. 49, December 6, 2024

Section 302.208 - Numeric Standards for Chemical Constituents

a) The acute standard (AS) for the chemical constituents listed in subsection (e) must not be exceeded at any time except for those waters for which a zone of initial dilution (ZID) has been approved by the Agency under Section 302.102.

b) The chronic standard (CS) for the chemical constituents listed in subsection (e) must not be exceeded by the arithmetic average of at least four consecutive samples collected over any period of at least four days, except for those waters in which the Agency has approved a mixing zone or in which mixing is allowed under 35 Ill. Adm. Code 302.102. The samples used to demonstrate attainment or lack of attainment with a CS must be collected in a manner that assures an average representative of the sampling period. For the chemical constituents that have water quality-based standards dependent upon hardness, the chronic water quality standard will be calculated according to subsection (e) using the hardness of the water body at the time the sample was collected. To calculate the attainment status of chronic standards, the concentration of the chemical constituent in each sample is divided by the calculated water quality standard for the sample to determine a quotient. The water quality standard is attained if the mean of the sample quotients is less than or equal to one for the duration of the averaging period.

c) The human health standard (HHS) for the chemical constituents listed in subsection (f) must not be exceeded when the streamflow is at or above the harmonic mean flow under Section 302.658, nor must an annual average, based on at least eight samples collected in a manner representative of the sampling period, exceed the HHS except for those waters in which the Agency has approved a mixing zone or in which mixing is allowed under Section 302.102.

d) The standard for the chemical constituents of subsections (g) and (h) must not be exceeded at any time except for those waters in which the Agency has approved a mixing zone or in which mixing is allowed under Section 302.102.

e) Numeric Water Quality Standards for the Protection of Aquatic Organisms

Click here to view image

f) Numeric Water Quality Standard for the Protection of Human Health

Constituent	(µg/L)
Mercury (total)	0.012
Benzene	310

where:

µg/L

=

micrograms per liter

g) Single-value standards apply at the following concentrations for these substances:

Constituent	Unit	Standard
Barium (total)	mg/L	5.0
Chloride (total)	mg/L	500
Iron (dissolved)	mg/L	1.0
Phenols	mg/L	0.1
Selenium (total)	mg/L	1.0
Silver (total)	µg/L	5.0

where:

mg/L	=	milligram per liter and
µg/L	=	microgram per liter

h) Water quality standards for sulfate are as follows:

1) At any point where water is withdrawn or accessed for purposes of livestock watering, the average of sulfate concentrations must not exceed 2,000 mg/L when measured at a representative frequency over a 30-day period.

2) The results of the following equations provide sulfate water quality standards in mg/L for the specified ranges of hardness (in mg/L as CaCO₃) and chloride (in mg/L) and must be met at all times:

A) If the hardness concentration of receiving waters is greater than or equal to 100 mg/L but less than or equal to 500 mg/L, and if the chloride concentration of waters is greater than or equal to 25 mg/L but less than or equal to 500 mg/L, then:

C = [1276.7 + 5.508(hardness) - 1.457(chloride)] * 0.65

where:

C

=

sulfate concentration

B) If the hardness concentration of waters is greater than or equal to 100 mg/L but less than or equal to 500 mg/L, and if the chloride concentration of waters is greater than or equal to 5 mg/L but less than 25 mg/L, then:

C = [-57.478 + 5.79(hardness) + 54.163(chloride)] * 0.65

where:

C

=

sulfate concentration

3) The following sulfate standards must be met at all times when hardness (in mg/L as CaCO₃) and chloride (in mg/L) concentrations other than specified in subsection (h)(2) are present:

A) If the hardness concentration of waters is less than 100 mg/L or chloride concentration of waters is less than 5 mg/L, the sulfate standard is 500 mg/L.

B) If the hardness concentration of waters is greater than 500 mg/L and the chloride concentration of waters is 5 mg/L or greater, the sulfate standard is 2,000 mg/L.

C) If the combination of hardness and chloride concentrations of existing waters are not reflected in subsection (h)(3)(A) or (B), the sulfate standard may be determined in a site-specific rulemaking under section 303(c) of the Federal Water Pollution Control Act of 1972 (Clean Water Act), 33 U.S.C. 1313(c), and Federal Regulations at 40 CFR 131.10(j)(2).

Ill. Admin. Code tit. 35, § 302.208

Amended at 37 Ill. Reg. 7493, effective May 16, 2013

Amended at 47 Ill. Reg. 4437, effective 3/23/2023