Ill. Admin. Code tit. 35 § 218.205

Current through Register Vol. 48, No. 49, December 6, 2024

Section 218.205 - Daily-Weighted Average Limitations

No owner or operator of a coating line subject to the limitations of Section 218.204 of this Subpart and complying by means of this Section shall operate the subject coating line unless the owner or operator has demonstrated compliance with subsection (a), (b), (c), (d), (e), (f), (g), (h), (i), (j), or (k) of this Section (depending upon the category of coating) through the applicable coating analysis test methods and procedures specified in Section 218.105(a) of this Part and the recordkeeping and reporting requirements specified in Section 218.211(d) of this Subpart:

a) No owner or operator of a coating line subject to only one of the limitations from among Section 218.204(a)(1)(A), (a)(1)(D), (a)(2)(A), (a)(2)(E), (a)(2)(F), (c)(1), (d), (e), (f), (i), or (p) of this Subpart shall apply coatings on any such coating line, during any day, whose daily-weighted average VOM content exceeds the emission limitation to which the coatings are subject.

b) Prior to May 1, 2012, no owner or operator of a miscellaneous metal parts and products coating line subject to the limitations of Section 218.204(j) of this Subpart shall apply coatings to miscellaneous metal parts or products on the subject coating line unless the requirements in subsection (b)(1) or (b)(2) of this Section are met.

1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(j) during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line which applies coatings subject to more than one numerical emission limitation in Section 218.204(j) of this Subpart, during the same day, the owner or operator shall have a site-specific proposal approved by the Agency and approved by the USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy), 51 Fed. Reg. 43814 (December 4, 1986), must be satisfied.

c) No owner or operator of a can coating line subject to the limitations of Section 218.204(b) of this Subpart shall operate the subject coating line using a coating with a VOM content in excess of the limitations specified in Section 218.204(b) of this Subpart unless all of the following requirements are met:

1) An alternative daily emission limitation shall be determined for the can coating operation, i.e., for all of the can coating lines at the source, according to subsection (c)(2) of this Section. Actual daily emissions shall never exceed the alternative daily emission limitation and shall be calculated by use of the following equation.

Image

where:

E_d	=	Actual VOM emissions for the day in units of kg/day (lbs/day);
i	=	Subscript denoting a specific coating applied;
n	=	Total number of coatings applied in the can coating operation, i.e., all can coating lines at the source;
V_i	=	Volume of each coating applied for the day in units of l/day (gal/day) of coating (minus water and any compounds that are specifically exempted from the definition of VOM);
C_i	=	The VOM content of each coating as applied in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds that are specifically exempted from the definition of VOM).

2) The alternative daily emission limitation (A_d) shall be determined for the can coating operation, i.e., for all of the can coating lines at the source, on a daily basis as follows:

Image

where:

A_d	=	The VOM emissions allowed for the day in units of kg/day (lbs/day);
i	=	Subscript denoting a specific coating applied;
n	=	Total number of surface coatings applied in the can coating operation;
C_i	=	The VOM content of each surface coating as applied in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds that are specifically exempted from the definition of VOM);
D_i	=	The density of VOM in each coating applied. For the purposes of calculating A_d, the density is 0.882 kg VOM/l VOM (7.36 lbs VOM/gal VOM);
V_i	=	Volume of each surface coating applied for the day in units of l (gal) of coating (minus water and any compounds that are specifically exempted from the definition of VOM);
L_i	=	The VOM emission limitation for each surface coating applied as specified in Section 218.204(b) of this Subpart in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds that are specifically exempted from the definition of VOM).

d) No owner or operator of a heavy off-highway vehicle products coating line subject to the limitations of Section 218.204(k) of this Subpart shall apply coatings to heavy off-highway vehicle products on the subject coating line unless the requirements of subsection (d)(1) or (d)(2) of this Section are met.

1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(k) of this Subpart, during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used: or

2) For each coating line which applies coatings subject to more than one numerical emission limitation in Section 218.204(k) of this Subpart, during the same day, the owner or operator shall have a site specific proposal approved by the Agency and approved by the USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy), 51 Fed. Reg. 43814 (December 4, 1986), must be satisfied.

e) No owner or operator of a wood furniture coating line subject to the limitations of Section 218.204(l)(1) or (l)(3) of this Subpart shall apply coatings to wood furniture on the subject coating line unless the requirements of subsection (e)(1) or subsection (e)(2) of this Section, in addition to the requirements specified in the note to Section 218.204(l)(1) of this Subpart, are met.

1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(l)(1) or (l)(3) of this Subpart, during the same day (e.g., all coatings used on the line are subject to 0.67 kg/l (5.6 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line which applies coatings subject to more than one numerical emission limitation in Section 218.204(l)(1) or (l)(3) of this Subpart, during the same day, the owner or operator shall have a site specific proposal approved by the Agency and approved by the USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy), 51 Fed. Reg. 43814 (December 4, 1986), must be satisfied.

f) No owner or operator of an existing diesel-electric locomotive coating line in Cook County, subject to the limitations of Section 218.204(m) of this Subpart shall apply coatings to diesel-electric locomotives on the subject coating line unless the requirements of subsection (f)(1) or (f)(2) of this Section are met.

1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(m) of this Subpart, during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line which applies coatings subject to more than one numerical emission limitation in Section 218.204(m) of this Subpart, during the same day, the owner or operator shall have a site specific proposal approved by the Agency and approved by the USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

g) Prior to May 1, 2012, no owner or operator of a plastic parts coating line, subject to the limitations of Section 218.204(n) or (o) of this Subpart shall apply coatings to business machine or automotive/transportation plastic parts on the subject coating line unless the requirements of subsection (g)(1) or (g)(2) of this Section are met:

1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(n) or (o) of this Subpart, during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line which applies coatings subject to more than one numerical emission limitation in Section 218.204(n) or (o) of this Subpart, during the same day, the owner or operator shall have a site specific proposal approved by the Agency and approved by the USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

h) No owner or operator of a metal furniture coating line, subject to the limitations of Section 218.204(g) of this Subpart shall apply coatings on the subject coating line unless the requirements of subsection (h)(1) or (h)(2) of this Section are met:

1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(g) of this Subpart, during the same day (e.g., all coatings used on the line are subject to 0.34 kg/l (2.8 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line which applies coatings subject to more than one numerical emission limitation in Section 218.204(g) of this Subpart, during the same day, the owner or operator shall have a site specific proposal approved by the Agency and approved by the USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

i) No owner or operator of a large appliance coating line, subject to the limitations of Section 218.204(h) of this Subpart shall apply coatings on the subject coating line unless the requirements of subsection (i)(1) or (i)(2) of this Section are met:

1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(h) of this Subpart, during the same day (e.g., all coatings used on the line are subject to 0.34 kg/l (2.8 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line which applies coatings subject to more than one numerical emission limitation in Section 218.204(h) of this Subpart, during the same day, the owner or operator shall have a site specific proposal approved by the Agency and approved by the USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

j) On and after May 1, 2011, no owner or operator of a paper coating line subject to the limitations of Section 218.204(c) of this Subpart shall apply coatings on the subject coating line unless the requirements in subsection (j)(1) or (j)(2) of this Section are met:

1) For each coating line that applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(c) during the same day (e.g., all coatings used on the line are subject to 0.40 kg/kg solids (0.08 kg/kg coatings)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line that applies coatings subject to more than one numerical emission limitation in Section 218.204(c) during the same day, the owner or operator shall have a site-specific proposal approved by the Agency and approved by USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy), 51 Fed. Reg. 43814 (December 4, 1986), must be satisfied.

k) On and after May 1, 2012, no owner or operator of a miscellaneous metal parts and products coating line, plastic parts or products coating line, pleasure craft surface coating line, or motor vehicle materials coating line subject to the limitations of Section 218.204(q) of this Subpart shall apply coatings on the subject coating line unless the requirements of subsection (k)(1) or (k)(2) of this Section are met:

1) For each coating line that applies multiple coatings, all of which are subject to the same numerical emission limitation within Section 218.204(q) of this Subpart, during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used; or

2) For each coating line that applies coatings subject to more than one numerical emission limitation in Section 218.204(q) of this Subpart, during the same day, the owner or operator shall have a site specific proposal approved by the Agency and approved by USEPA as a SIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

Ill. Admin. Code tit. 35, § 218.205

Amended at 34 Ill. Reg. 14174, effective September 14, 2010