Section R649-9-3 - Permit and Application Requirements for Disposal Facilities1. No waste disposal facility shall operate without a division-issued permit.2. Applications for new disposal facilities or modifications shall be submitted to the division and shall include the following:2.1. Previously submitted material may be included by reference provided they are current and readily available to the division.2.2. Evidence justifying the need for the proposed facility or expansion of an existing facility.2.3. Names and addresses of all applicants, principal officers and owners with 25 percent or more interest in the facility.2.4. Materials or products to be applied to the land surface or subsurface shall meet the division's current cleanup levels for contaminated soil and other wastes.2.5. If leachability and/or toxicity are of concern due to the type or source(s) of wastes, tests will be required and may utilize the Toxicity Characteristic Leaching Procedure (TCLP), Synthetic Precipitation Leaching Procedure (SPLP) or any other test approved by the division.2.6. A contingency plan designed to minimize any hazards to fresh water, public health and safety, or the environment in the event of an unplanned fire, explosion, or a release of contaminants or oil field waste to the air, soil, surface water or ground water.2.7. A solid waste stream management plan describing all chemical processes, estimated volumes and chemical profiles used in the treatment of waste and odor, any products generated by these processes, method and schedule for disposal of precipitated solids and complete list of all wastes to be accepted at the facility.2.8. A topographic map and drawing of the site, on a suitable scale, that identifies all geologic cross sections, side slopes, equipment, secondary containment, test borings, roads, fences, gates, wells and springs, drainage patterns, pipelines, surface area to be disturbed, buildings and chemical storage areas within one mile of the site perimeter and location relative to other site facilities. The drawings shall be of professional quality.3. Siting requirements for new disposal facilities and modifications.3.1. The disposal facility shall be located on level, stable ground, and an acceptable distance away from any established or intermittent drainage.3.2. The disposal facility shall be located a minimum of one mile from residences or occupied buildings not associated with the facility unless a wavier has been signed by the owners of the residences and buildings within one mile.4. Geologic and hydrological requirements for new disposal facilities or modifications.4.1. The disposal facility shall not be located in a geologically or hydrologically unsuitable area, such as aquifer recharge areas, protection zones for public drinking water sources, flood plains, drainage bottoms, and areas on or near faults, within 500 feet of a wetland, water-course or lakebed, permeable soil where ground water is less than 50 feet below the lowest elevation at which the operator will place oilfield waste, or within the area overlying a subsurface mine.4.2. Regional and local geologic information shall include bedrock strike and dip, fracture patterns, slope stability, faulting, folding, rockfall, landslides, subsidence or erosion potential, and surface water features that may affect the design and operation of the facility.4.3. Geological and hydrological evidence showing that the proposed disposal method will not adversely affect existing water quality or major uses of such waters. 4.3.1. Any intentional discharge of water will require an additional permit from the Division of Water Quality.4.4. Test borings shall be taken in sufficient quantity and to an adequate depth, not to exceed 50 feet, to define subsurface conditions to assure that the facility will be constructed on a firm stable base.4.5. Representative analysis of facility surface and subsurface soils submitted to the division shall include TDS, major cations and anions or other analysis determined necessary by the division for establishing background soil concentrations.4.6. Geologic cross-sections submitted to the division shall include depth to shallow ground water, formation names, and type and name of the shallowest fresh water aquifer beneath the proposed site.4.7. If determined necessary by the division, applicant shall submit ground water analysis of the aquifer(s) beneath the proposed site.4.8. If determined necessary by the division, applicant shall submit potentiometric maps of the shallowest aquifer(s).5. Engineering and design requirements for new disposal facilities and modifications. 5.1. Disposal facilities shall be designed and sealed by a registered engineer and inspected by a registered engineer during construction.5.1.1. A construction certification shall be submitted, by the engineer, prior to the Division issuing an operation permit for the facility.5.2. The disposal facility shall be designed appropriately for the intended purpose.5.3. Facilities shall be designed, constructed and operated so as to contain liquids and solids in a manner that will protect fresh water, public health and safety, and the environment for the life of the operation.5.3.1. The disposal facility shall be designed with secondary containment to capture the largest potential release in the event of a catastrophic failure.5.4. Facilities shall be designed and constructed so as to prevent run-on and run-off of surface water, up to peak discharge from a 25 year, 24 hour storm.5.5. The facility shall be designed such that disposal can only occur when an attendant is on duty, unless loads can be monitored or otherwise isolated for inspection before disposal or other security measures approved by the division.Utah Admin. Code R649-9-3