Current through Register Vol. 48, No. 07, July 26, 2024
Section 61-86.1.XIII - OPERATION AND MAINTENANCE ACTIVITIESA. Applicability. 1. The notification/application, work practice, clean-up, and disposal requirements of this Section shall apply to the non-industrial facility owner/operator and the O&M personnel covered under the facility's group license.2. Workers are limited to an activity in which the amount of RACM disturbed does not exceed that which can be contained in one glovebag or one 6-mil polyethylene bag measuring no greater than 60 inches in length and width.B. Notification/Application. In a facility being abated that is subject to this Section:
1. The non-industrial facility owner/operator shall provide the Department with written notification/application and pay all applicable fees as follows: a. Acceptable delivery of the notification shall be by U.S. Postal Service, commercial delivery service, facsimile transmission, by hand or by other methods deemed acceptable by the Department.b. Update the notification when any previously-notified information changes.c. Notify the Department by telephone and follow up in writing as soon as possible, but not later than, the original start date when a project for which notification was made has been canceled.2. Alternately, facility employees who do not meet the definition of a contractor as defined by this regulation may maintain a log of all O&M activities performed during a quarter, report them to the Department within 30 calendar days of the end of the quarter, and pay applicable project fees. The log shall include, but is not limited to: the name and address of the facility being abated, amount and type of ACM removed, date(s) of removal, names of individuals who performed the abatement, exact location for temporary storage of asbestos wastes, and the name of the landfill used for disposal.C. Air Sampling and Analysis Procedures. The facility owner shall ensure that sampling is performed in accordance with applicable requirements of the Air Sampling Section of this regulation.
D. Work Practice and Clean-Up Requirements.1. An owner/operator engaged in an operation and maintenance activity shall: a. Construct critical barriers to prevent the potential release of asbestos fibers from within the work area;b. Wet all RACM prior to removal and during containerization for disposal at an approved landfill;c. Prevent track-out and leakage of RACM onto uncontaminated surfaces;d. Use HEPA vacuum equipment and wet-cleaning techniques to clean up the work area following abatement until there is no visible residue;e. Ensure that ACM from within the work area is not permitted outside of the work area except in sealed leak-tight containers;f. Containerize wetted waste in appropriately labeled impermeable containers (6-mil polyethylene sheeting, bags, and/or fiber or metal drums) and store in an area that is secured and locked;g. Transport asbestos waste in a manner that does not release fibers into the air, and dispose of at a landfill permitted to accept asbestos waste.2. Each owner/operator engaged in an O&M glovebag operation shall:a. Ensure that the glovebag procedure is being performed only by persons who have received training in the method and are licensed as workers or supervisors in accordance with the requirements of this regulation;b. Ensure that the glovebag is constructed and utilized in accordance with the glovebag requirements of this regulation and OSHA 29 CFR 1926.1101, as amended, and any subsequent amendments and editions;c. Isolate the work area to prevent access by unprotected persons;d. Display danger signs in accordance with OSHA 29 CFR 1926.1101, as amended, and any subsequent amendments and editions, at all approaches to any asbestos abatement area;e. Remove all polyethylene sheeting, tape, glovebags and other equipment, and inspect the area for visible residue following abatement;f. Wet-clean the area using amended water and a HEPA vacuum after surfaces have been allowed to dry. The sequence of wet cleaning and vacuuming shall be repeated until no visible residue is observed in the work area; andg. Ensure that porous surfaces that have been stripped or cleaned of RACM are encapsulated to secure any residual fibers that may be present. The encapsulant used must be compatible with subsequent coverings.E. Disposal. The owner/operator shall comply with the requirements of the Disposal Section of this regulation.
S.C. Code Regs. 61-86.1.XIII