AGENCY:
Federal Aviation Administration (FAA), DOT.
ACTION:
Notice of proposed rulemaking (NPRM).
SUMMARY:
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
One LM-219-92 Centre Bracket from an LM-219-SA28 Aft Engine Mounting assembly was found to be cracked while installed on the aircraft.
This reduces the effectiveness of the mounting assembly and could eventually cause it to fail.
A failed mounting assembly, if not corrected, could result in loss of the engine. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.
DATES:
We must receive comments on this proposed AD by March 6, 2008.
ADDRESSES:
You may send comments by any of the following methods:
- Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
- Fax: (202) 493-2251.
- Mail: U.S. Department of Transportation, Docket Operations,M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
- Hand Delivery: U.S. Department of Transportation, Docket Operations,M-30, West Building Ground Floor, Room W12-40, 1200 New Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov ; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT:
Shahram Daneshmandi, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1112; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2008-0115; Directorate Identifier 2007-NM-240-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.
We will post all comments we receive, without change, to http://www.regulations.gov,, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.
Discussion
The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA Airworthiness Directive 2007-0204, dated August 8, 2007 (referred to after this as “the MCAI”), to correct an unsafe condition for the specified products. The MCAI states:
One LM-219-92 Centre Bracket from an LM-219-SA28 Aft Engine Mounting assembly was found to be cracked while installed on the aircraft.
This reduces the effectiveness of the mounting assembly and could eventually cause it to fail.
This AD requires rework in order to make the centre bracket less sensitive to external damage that may result in a crack.
A failed mounting assembly, if not corrected, could result in loss of the engine. The corrective action also includes a visual and fluorescent penetrant inspection for cracking of the center bracket of the aft engine mounting assembly for both engines, re-identification of a reworked center bracket, additional fluorescent penetrant inspections for cracking of the reworked center bracket, and replacement of the aft engine mounting assembly if any cracked center bracket is found. You may obtain further information by examining the MCAI in the AD docket.
Relevant Service Information
Saab has issued Saab 2000 Service Bulletin 2000-71-025, dated June 13, 2007. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD.
Costs of Compliance
Based on the service information, we estimate that this proposed AD would affect about 6 products of U.S. registry. We also estimate that it would take about 8 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $80 per work-hour. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $3,840, or $640 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation:
1. Is not a “significant regulatory action” under Executive Order 12866;
2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
- Air transportation
- Aircraft
- Aviation safety
- Safety
The Proposed Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39—AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
2. The FAA amends § 39.13 by adding the following new AD:
SAAB Aircraft AB: Docket No. FAA-2008-0115; Directorate Identifier 2007-NM-240-AD.
Comments Due Date
(a) We must receive comments by March 6, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Saab Model SAAB 2000 airplanes, certificated in any category, serial number 004 through 063.
Subject
(d) Air Transport Association (ATA) of America Code 71: Power Plant.
Reason
(e) The mandatory continuing airworthiness information (MCAI) states:
One LM-219-92 Centre Bracket from an LM-219-SA28 Aft Engine Mounting assembly was found to be cracked while installed on the aircraft.
This reduces the effectiveness of the mounting assembly and could eventually cause it to fail.
This AD requires rework in order to make the centre bracket less sensitive to external damage that may result in a crack.
A failed mounting assembly, if not corrected, could result in loss of the engine. The corrective action also includes a visual and fluorescent penetrant inspection for cracking of the center bracket of the aft engine mounting assembly for both engines, re-identification of a reworked center bracket, additional fluorescent penetrant inspections for cracking of the reworked center bracket, and replacement of the aft engine mounting assembly if any cracked center bracket is found.
Actions and Compliance
(f) Unless already done, do the following actions in accordance with the Accomplishment Instructions of Saab 2000 Service Bulletin 2000-71-025, dated June 13, 2007.
(1) Within 1,000 flight hours after the effective date of this AD, do a visual and a fluorescent penetrant inspection for cracking of the center bracket of both of the aft engine mounting assemblies.
(2) If no cracking is found during the inspections required by paragraph (f)(1) of this AD, within 4,000 flight hours after the effective date of this AD, rework the center bracket of the aft engine mounting assembly, do fluorescent penetrant inspections for cracking of the reworked bracket, and re-identify with new part numbers the reworked center bracket and the applicable aft engine mounting assembly.
(3) If any cracking is found during any inspection required by paragraph (f)(1) or (f)(2) of this AD, before further flight, replace the aft engine mounting assembly, and rework and re-identify the center bracket.
FAA AD Differences
Note:
This AD differs from the MCAI and/or service information as follows:
(1) Although the MCAI or service information allows further flight after cracks are found during compliance with the required action, paragraph (f)(3) of this AD requires that you replace the aft engine mounting assembly before further flight.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, Transport Airplane Directorate, ANM-116, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Shahram Daneshmandi, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1112; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056.
Related Information
(h) Refer to MCAI European Aviation Safety Agency (EASA) Airworthiness Directive 2007-0204, dated August 8, 2007, and Saab 2000 Service Bulletin 2000-71-025, dated June 13, 2007, for related information.
Issued in Renton, Washington, on January 24, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. E8-1992 Filed 2-4-08; 8:45 am]
BILLING CODE 4910-13-P