Airworthiness Directives; Bombardier, Inc., Airplanes

Download PDF
Federal RegisterFeb 8, 2022
87 Fed. Reg. 7056 (Feb. 8, 2022)

AGENCY:

Federal Aviation Administration (FAA), DOT.

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes. This proposed AD was prompted by a report of smoke in the aft cabin during a maintenance activity, which an investigation determined was caused by a faulty drain line ribbon heater. This proposed AD would require a general visual inspection of all affected potable water-line ribbon heater installations and corrective actions and other specified actions. The FAA is proposing this AD to address the unsafe condition on these products.

DATES:

The FAA must receive comments on this proposed AD by March 25, 2022.

ADDRESSES:

You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.

Fax: 202-493-2251.

Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this NPRM, contact Bombardier Business Aircraft Customer Response Center, 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone 514-855-2999; email ac.yul@aero.bombardier.com; internet http://www.bombardier.com. You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

Examining the AD Docket

You may examine the AD docket at https://www.regulations.gov by searching for and locating Docket No. FAA-2022-0090; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, any comments received, and other information. The street address for Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT:

Thomas Niczky, Aerospace Engineer, Avionics and Electrical Systems Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7347; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under ADDRESSES . Include “Docket No. FAA-2022-0090; Project Identifier MCAI-2021-00399-T” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend the proposal because of those comments.

Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to https://www.regulations.gov,, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM.

Confidential Business Information

CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Thomas Niczky, Aerospace Engineer, Avionics and Electrical Systems Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7347; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.

Background

Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued TCCA AD CF-2021-13, dated April 1, 2021 (TCCA AD CF-2021-13) (also referred to after this as the Mandatory Continuing Airworthiness Information, or the MCAI), to correct an unsafe condition for Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes, equipped with any Cox & Co. 3043 or 3044 series (potable water-line) ribbon heater. You may examine the MCAI in the AD docket at https://www.regulations.gov by searching for and locating Docket No. FAA-2022-0090.

This proposed AD was prompted by a report of smoke in the aft cabin during a maintenance activity, which an investigation determined was caused by a faulty drain line ribbon heater. The ribbon heater lead wires were found to have been installed with the lead wire termination reversed, which, in combination with a ribbon heater ground fault, led to a continuous ribbon heater heating condition. The FAA is proposing this AD to address faulty potable water-line ribbon heaters, which, if not corrected, could lead to an onboard fire. See the MCAI for additional background information.

Related Service Information Under 1 CFR Part 51

Bombardier has issued Service Bulletin 601-0644, Revision 1, dated January 29, 2019, and Service Bulletin 604-30-007, Revision 1, dated January 29, 2019. This service information describes procedures for a general visual inspection of all affected potable water-line ribbon heater installations for any discrepancy and applicable corrective actions and other specified actions. Discrepancies include discoloration, blistering or cracking of insulation, signs of wear, or heat damage. Corrective actions include replacement of discrepant insulation and ribbon heaters. Other specified actions include identifying the potable water-line ribbon heater pigtail wire configuration, installing a fuse to the ribbon heater power lead, and testing the potable water-line heater system of each ribbon heater. These documents are distinct since they apply to different airplane models. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

FAA's Determination

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to the FAA's bilateral agreement with the State of Design Authority, the FAA has been notified of the unsafe condition described in the MCAI and service information referenced above. The FAA is proposing this AD because the FAA evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design.

Proposed AD Requirements in This NPRM

This proposed AD would require accomplishing the actions specified in the service information already described.

Costs of Compliance

The FAA estimates that this AD, if adopted as proposed, would affect 585 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:

Estimated Costs for Required Actions

Labor cost Parts cost Cost per product Cost on U.S. operators
Up to 30 work-hours × $85 per hour = Up to $2,550 $268 Up to $2,818 Up to $1,648,530.

The FAA estimates the following costs to do any necessary on-condition action that would be required based on the results of any required actions. The FAA has no way of determining the number of aircraft that might need this on-condition action:

Estimated Costs of On-Condition Actions

Labor cost Parts cost Cost per product
Up to 30 work-hours × $85 per hour = $2,550 Up to $39,552 * $42,102
* The parts cost for a single potable water-line ribbon heater and associated material is $4,944. The estimated cost above assumes the worst case scenario of replacing all eight ribbon heaters on an airplane configured with eight ribbon heaters.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Will not affect intrastate aviation in Alaska, and

(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

  • Air transportation
  • Aircraft
  • Aviation safety
  • Incorporation by reference
  • Safety

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13
[Amended]

2. The FAA amends § 39.13 by adding the following new airworthiness directive:

Bombardier, Inc.: Docket No. FAA-2022-0090; Project Identifier MCAI-2021-00399-T.

(a) Comments Due Date

The FAA must receive comments on this airworthiness directive (AD) by March 25, 2022.

(b) Affected ADs

None.

(c) Applicability

This AD applies to Bombardier, Inc., airplanes certificated in any category, identified in paragraphs (c)(1) through (3) of this AD and equipped with any Cox & Co. 3043 or 3044 series (potable water-line) ribbon heater.

(1) Model CL-600-1A11 (600) airplanes.

(2) Model CL-600-2A12 (601) airplanes.

(3) Model CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes.

(d) Subject

Air Transport Association (ATA) of America Code 3070, Ice and Rain Protection; Code 3810, Potable Water System.

(e) Unsafe Condition

This AD was prompted by a report of smoke in the aft cabin during a maintenance activity, which an investigation determined was caused by a faulty drain line ribbon heater. The FAA is issuing this AD to address faulty potable water-line ribbon heaters, which, if not corrected, could lead to an onboard fire.

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Inspection of Potable Water-Line Ribbon Heater Installation and Insulation, Applicable Corrective Actions, and Other Specified Actions

For airplanes with a serial number listed in Section 1.A of the applicable service information specified in figure 1 to paragraph (g) of this AD: Within 6 years after the effective date of this AD, do an inspection of the potable water-line ribbon heater installation and insulation to detect any discrepancy, and, before further flight, do all applicable corrective actions and other specified actions in accordance with the Accomplishment Instructions of the service information specified in figure 1 to paragraph (g) of this AD, as applicable.

(h) Required Actions for Airplanes Not Listed in the Service Information

For airplanes with a serial number that is not listed in section 1.A of the service information specified in figure 1 to paragraph (g) of this AD, and for Bombardier Model CL-600-1A11 airplanes: Within 6 years after the effective date of this AD, do applicable actions including inspection for discrepancies of the potable water-line ribbon heater and repair of any discrepant potable water-line ribbon heaters using a method approved in accordance with the procedures specified in paragraph (i)(2) of this AD.

(i) Other FAA AD Provisions

The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, New York ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.

(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, New York ACO Branch, FAA; or Transport Canada Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature.

(j) Related Information

(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) Canadian AD CF-2021-13, dated April 1, 2021, for related information. This MCAI may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2022-0090.

(2) For more information about this AD, contact Thomas Niczky, Aerospace Engineer, Avionics and Electrical Systems Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7347; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

(3) For service information identified in this AD, contact Bombardier Business Aircraft Customer Response Center, 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone 514-855-2999; email ac.yul@aero.bombardier.com; internet http://www.bombardier.com. You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

Issued on February 2, 2022.

Gaetano A. Sciortino,

Deputy Director for Strategic Initiatives, Compliance & Airworthiness Division, Aircraft Certification Service.

[FR Doc. 2022-02513 Filed 2-7-22; 8:45 am]

BILLING CODE 4910-13-P