Airworthiness Directives; Airbus SAS Airplanes

Download PDF
Federal RegisterMar 22, 2024
89 Fed. Reg. 20364 (Mar. 22, 2024)

AGENCY:

Federal Aviation Administration (FAA), DOT.

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

The FAA proposes to supersede Airworthiness Directive (AD) 2022–14–10, which applies to certain Airbus SAS Model A318 series airplanes; Model A319–111, –112, –113, –114, –115, –131, –132, and –133 airplanes; Model A320–211, –212, –214, –216, –231, –232, and –233 airplanes; and Model A321–111, –112, –131, –211, –212, –213, –231, and –232 airplanes. AD 2022–14–10 requires repetitive inspections for cracking of the radius of the front spar vertical stringers and the horizontal floor beam on a certain frame (FR), repetitive inspections for cracking of the fastener holes of the front spar vertical stringers on that frame, and repair if necessary. AD 2022–14–10 provides, for certain airplanes, a modification of the center wing box area that terminates the repetitive inspections under certain conditions. Since the FAA issued AD 2022–14–10, an additional airplane model has been identified that is also subject to the unsafe condition. This proposed AD would continue to require the actions in AD 2022–14–10 and would add Model A321–271N airplanes to the applicability, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.

DATES:

The FAA must receive comments on this proposed AD by May 6, 2024.

ADDRESSES:

You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to regulations.gov. Follow the instructions for submitting comments.

Fax: 202–493–2251.

Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590.

Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA–2024–0757; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above.

Material Incorporated by Reference:

• For the EASA AD identified in this NPRM, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu. It is also available at regulations.gov under Docket No. FAA–2024–0757.

  • You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195.

FOR FURTHER INFORMATION CONTACT:

Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 817–222–5102; email timothy.p.dowling@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under ADDRESSES . Include “Docket No. FAA–2024–0757; Project Identifier MCAI–2023–01205–T” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments.

Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM.

Confidential Business Information

CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 817–222–5102; email timothy.p.dowling@faa.gov. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.

Background

The FAA issued AD 2022–14–10, Amendment 39–22115 (87 FR 42315, July 15, 2022) (AD 2022–14–10), for certain Airbus SAS Model A318 series airplanes; Model A319–111, –112, –113, –114, –115, –131, –132, and –133 airplanes; Model A320–211, –212, –214, –216, –231, –232, and –233 airplanes; and Model A321–111, –112, –131, –211, –212, –213, –231, and –232 airplanes. AD 2022–14–10 was prompted by an MCAI originated by EASA, which is the Technical Agent for the Member States of the European Union. EASA issued AD 2021–0241, dated November 8, 2021 (EASA AD 2021–0241), to correct an unsafe condition. EASA AD 2021–0241 stated that during full-scale certification fatigue testing of the center fuselage, cracks were found on a wing front spar vertical stringer at FR36.

AD 2022–14–10 requires repetitive inspections for cracking of the radius of the front spar vertical stringers and the horizontal floor beam on frame (FR) 36, repetitive inspections for cracking of the fastener holes of the front spar vertical stringers on FR 36, and repair if necessary, and, for certain airplanes, a potential terminating action modification of the center wing box area. The FAA issued AD 2022–14–10 to address fatigue cracking of the front spar vertical stringers on the wings, which, if not corrected, could result in the reduced structural integrity of the airplane.

Actions Since AD 2022–14–10 Was Issued

Since the FAA issued AD 2022–14–10, EASA superseded EASA AD 2021–0241, dated November 8, 2021, and issued EASA AD 2023–0205, dated November 21, 2023 (EASA AD 2023–0205) (also referred to as the MCAI), to correct an unsafe condition for certain Airbus SAS Model A318 series airplanes; Model A319–111, –112, –113, –114, –115, –131, –132, and –133 airplanes; Model A320–211, –212, –214, –215, –216, –231, –232, and –233 airplanes; and Model A321–111, –112, –131, –211, –212, –213, –231, –232, and –271N airplanes. Model A320–215 airplanes are not certificated by the FAA and are not included on the U.S. type certificate data sheet; this AD, therefore, does not include those airplanes in the applicability. The MCAI states that analysis of the full-scale certification fatigue testing findings indicated that Model A321–271N airplanes are also subject to the unsafe condition. Fatigue cracking of the front spar vertical stringers on the wings, if not detected and corrected, could lead to crack propagation, possibly resulting in reduced structural integrity of the airplane.

The FAA is proposing this AD to address the unsafe condition on these products. You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA–2024–0757.

Explanation of Retained Requirements

Although this proposed AD does not explicitly restate the requirements of AD 2022–14–10, this proposed AD would retain all of the requirements of AD 2022–14–10. Those requirements are referenced in EASA AD 2023–0205, which, in turn, is referenced in paragraph (g) of this proposed AD.

Related Service Information Under 1 CFR Part 51

EASA AD 2023–0205 specifies procedures for repetitive special detailed inspections for cracking of the radius of the front spar vertical stringers, horizontal floor beam radius and fastener holes of the front spear vertical stringers on frame 36, and for installing new fasteners. EASA AD 2023–0205 further describes procedures for repetitive high frequency eddy current (HFEC) inspections for cracking of the horizontal floor beam, repetitive HFEC inspections for cracking of the fastener holes of the front spar vertical stringers on FR 36, repetitive rototest inspections of the fastener holes of the spar vertical stringers, and repair. EASA AD 2023–0205 also describes procedures for the modification of the center wing box area. The modification is required for airplanes in configuration 1, 2 or 3; and for airplanes in configuration 5, 6, or 7, the modification is optional and is a terminating action for the repetitive inspections when done within a specified time frame. The modification includes related investigative and corrective actions. Related investigative actions include an HFEC inspection on the radius of the rib flanges, a rototest inspection of the fastener holes, detailed and HFEC inspections for cracking on the cut edges, detailed and rototest inspections on all open fastener holes, and an inspection to determine if secondary structure brackets are installed. Corrective actions include rework of the secondary structure bracket and repair.

This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

FAA's Determination

This product has been approved by the aviation authority of another country and is approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, it has notified the FAA of the unsafe condition described in the MCAI referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design.

Proposed AD Requirements in This NPRM

This proposed AD would retain all requirements of AD 2022–14–10. This proposed AD would add airplanes to the applicability and require accomplishing the actions specified in EASA AD 2023–0205 described previously, except for any differences identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

In the FAA's ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to incorporate EASA AD 2023–0205 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2023–0205 in its entirety through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in EASA AD 2023–0205 does not mean that operators need comply only with that section. For example, where the AD requirement refers to “all required actions and compliance times,” compliance with this AD requirement is not limited to the section titled “Required Action(s) and Compliance Time(s)” in EASA AD 2023–0205. Service information required by EASA AD 2023–0205 for compliance will be available at regulations.gov under Docket No. FAA–2024–0757 after the FAA final rule is published.

Costs of Compliance

The FAA estimates that this AD, if adopted as proposed, would affect 1,755 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:

Estimated Costs for Required Actions

Action Labor cost Parts cost Cost per product Cost on U.S. operators
Inspection, per inspection cycle 25 work-hours × $85 per hour = $2,125 Up to $100 Up to $2,225 Up to $3,904,875.

Estimated Costs for Optional Actions

Labor cost Parts cost Cost per product
Up to 409 work-hours × $85 per hour = $34,765 Up to $66,050 Up to $100,815.

The FAA has received no definitive data on which to base the cost estimates for the on-condition actions specified in this proposed AD.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Would not affect intrastate aviation in Alaska, and

(3) Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

  • Air transportation
  • Aircraft
  • Aviation safety
  • Incorporation by reference
  • Safety

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13
[Amended]

2. The FAA amends § 39.13 by:

a. Removing Airworthiness Directive (AD) 2022–14–10, Amendment 39–22115 ( 87 FR 42315, July 15, 2022); and

b. Adding the following new AD:

Airbus SAS: Docket No. FAA–2024–0757; Project Identifier MCAI–2023–01205–T.

(a) Comments Due Date

The FAA must receive comments on this airworthiness directive (AD) by May 6, 2024.

(b) Affected ADs

This AD replaces AD 2022–14–10, Amendment 39–22115 (87 FR 42315, July 15, 2022) (AD 2022–14–10).

(c) Applicability

This AD applies to the Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2023–0205, dated November 21, 2023 (EASA AD 2023–0205).

(1) Model A318–111, –112, –121, and –122 airplanes.

(2) Model A319–111, –112, –113, –114, –115, –131, –132, and –133 airplanes.

(3) Model A320–211, –212, –214, –216, –231, –232, and –233 airplanes.

(4) Model A321–111, –112, –131, –211, –212, –213, –231, –232, and –271N airplanes.

(d) Subject

Air Transport Association (ATA) of America Code 57, Wings.

(e) Unsafe Condition

This AD was prompted by a report that, during a center fuselage certification full-scale fatigue test, cracks were found on the front spar vertical stringer at a certain frame. This AD was also prompted by a determination that Model A321 airplanes that have incorporated modification 160021 are also subject to the unsafe condition. The FAA is issuing this AD to address fatigue cracking of the front spar vertical stringers on the wings. The unsafe condition, if not addressed, could result in reduced structural integrity of the airplane.

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Requirements

Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2023–0205.

(h) Exceptions to EASA AD 2023–0205

(1) Where EASA AD 2023–0205 refers to “22 November 2021 [the effective date of EASA AD 2021–0241],” this AD requires using August 19, 2022 (the effective date of AD 2022–14–10).

(2) Where EASA AD 2023–0205 refers to its effective date, this AD requires using the effective date of this AD.

(3) This AD does not adopt the “Remarks” section of EASA AD 2023–0205.

(4) Where paragraph (5) of EASA AD 2023–0205 specifies “if any crack is found, before next flight, contact Airbus for approved corrective action instructions and accomplish those instructions accordingly,” this AD requires replacing that text with “if any crack is found, the crack must be repaired before further flight using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.”

(i) No Reporting Requirement

Although the service information referenced in EASA AD 2023–0205 specifies to submit certain information to the manufacturer, this AD does not include that requirement.

(j) Additional AD Provisions

The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, mail it to the address identified in paragraph (k) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.

(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.

(3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.

(k) Additional Information

For more information about this AD, contact Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 817–222–5102; email timothy.p.dowling@faa.gov.

(l) Material Incorporated by Reference

(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise.

(i) European Union Aviation Safety Agency (EASA) AD 2023–0205, dated November 21, 2023.

(ii) [Reserved]

(3) For EASA AD 2023–0205, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu.

(4) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195.

(5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email fr.inspection@nara.gov.

Issued on March 15, 2024.

Victor Wicklund,

Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service.

[FR Doc. 2024–05914 Filed 3–21–24; 8:45 am]

BILLING CODE 4910–13–P