From Casetext: Smarter Legal Research

Wren v. Kennedy Valve Manufacturing Co.

Appellate Division of the Supreme Court of New York, Third Department
Nov 13, 1907
122 App. Div. 289 (N.Y. App. Div. 1907)

Opinion

November 13, 1907.

A.J. Nellis and John A. Delehanty, for the appellant.

Mark Cohn and John W. Walsh, for the respondent.


Plaintiff's decedent, Thomas Wren, died in consequence of being burned by molten iron while working for the defendant in its foundry at Coxsackie, N.Y., on the evening of December 19, 1900. Negligence of the defendant in causing such injury is alleged as the reason why the judgment which plaintiff has recovered herein should be sustained. The molten iron was poured into a cylindrical-shaped ladle capable of holding about one ton and this ladle with its contents was transported by means of a crane to different parts of the foundry where the molten iron was used by the various workmen. On either side of the ladle and extending outwardly therefrom was a round projection called a shank about two inches in diameter. When the ladle was filled and ready for transportation both these shanks were grasped by hooks at the ends of an arched-shaped bail the center of which bail was attached to the crane. These were ordinary hooks made by bending the bail at its extremities outward and upward so that the hooks could be placed beneath the shanks of the ladle, and when the latter was lifted by the crane the shanks would rest securely in the curve of the hooks if properly adjusted. It was the duty of one of the workmen to adjust these hooks around the shanks of the ladle when the latter was filled with the molten metal. At the time of the accident this adjustment had been supposedly made and the ladle with its burden had been transported to another part of the foundry where the deceased was to receive it. As the ladle reached its destination it was discovered by one of the workmen that one of the shanks instead of resting in the curve of the hook rested on the end of its shorter side. An alarm was given to lower the ladle so that the proper adjustment could be made, but before this could be accomplished the ladle slipped from the hook and its contents fell upon the deceased, causing the injuries which resulted in his death.

It is claimed that the hook was defective and unsafe because the end of the prong or side thereof on which the shank rested protruded or curved too much outwardly so that there was a tendency for the shank to catch and rest thereon instead of slipping into the bend or curve at the bottom of the hook. This bail, with the hooks in the same condition, had been in frequent use for at least three years. During that time no accident had occurred.

The respondent urges on our attention the case of Welle v. Celluloid Company ( 175 N.Y. 401). In that case the mechanism and the defect therein which was responsible for the accident were strikingly similar to that which existed here. A judgment of nonsuit was affirmed by the Appellate Division. ( 52 App. Div. 522. ) It was held by a bare majority of the Court of Appeals that the case was a close one, but that it should have been submitted to the jury. There was, however, an important distinction between that case and this, and on that distinction the opinion of the latter court seems to have turned as to the question of the defendant's negligence. In that case the form of the hook had been changed shortly before the accident, and the court said: "No reason appears why the form of hook was changed. In making that change the defendant was bound to to use reasonable care to see that the new appliance was equally safe with the old, and the jury might have found that the master was chargeable with knowledge of the danger caused by the change which would not be imputed to a common laborer. It is in this respect that the present case is to be differentiated from that of Burke v. Witherbee ( 98 N.Y. 562). There the appliance, the failure of which caused the accident, had worked safely for a long period, and there was no proof that the master should have known that in any way it was unsuitable for the purpose for which it was used. The proof here is to the contrary."

It will be observed that in the Welle case it was stated that "the jury might have found that the master was chargeable with knowledge of the danger caused by the change which would not be imputed to a common laborer," and that seems to be the only circumstance or at least the principal circumstance on which it was held that negligence could be predicated. Here there had been no change in the bail or its hooks and that circumstance does not exist. I think this case is differentiated from the Welle case and is controlled by the principles enunciated in Burke v. Witherbee, cited and distinguished in the Welle case.

In Burke v. Witherbee the accident also happened because of the slipping of an iron hook. The work would seem to have been just as dangerous as the work in defendant's foundry. The court said: "The defendants did not owe the duty to their workmen to furnish the best known or the best conceivable appliances; but they were under a duty to furnish reasonably safe and suitable appliances — such as a prudent man would furnish if his own life were exposed to the danger that would result from unsuitable or defective appliances."

It is true that one witness testified that six or eight months before the accident the shank rested on the end of the outer side of the hook, but it was discovered and the ladle lowered without accident. Another witness testified that on half a dozen different occasions when he was adjusting the hooks to the shank he discovered before the ladle was elevated that the shanks caught "on the point of the hook," as he expressed it. It is quite apparent, however, that this might have occurred if there had been no flare or protrusion at the end of the outer side. No matter what the details of the construction, unless care were used in the proper adjustment the shank, because of the pressure of the superimposed weight, might have poised and balanced on the shorter side of the hook and subsequently slipped off. This latter witness also testified that the point of the hook projected forward and had a flat spot on it presenting an inch and a half surface. It does not appear how long it had been in that condition. It may have been bent and flattened at the time of the accident by the weight which then rested upon it. It is quite strange that if it had been in that condition some of the workmen would not have observed it prior to the accident. Neither of these witnesses made any report or suggestion of danger to the defendant or its superintendent. None of the workmen who operated these hooks and who must necessarily have been cognizant of their danger, if danger there was, made any suggestion of their inadequacy or insufficiency. The defendant operated a blacksmith shop in connection with its foundry and as the evidence shows the hook might have been straightened without expense, trouble or inconvenience. If the hook were unsafe the lives of these witnesses were in jeopardy, and the best evidence that they did not believe it to be unsafe is the fact that as they say with knowledge of its condition they continued to operate it without complaint although with no appreciable trouble or inconvenience it might have been changed. The only natural inference is that the hook itself was not suggestive of danger.

In the Burke case as here one or more witnesses testified to the prior slipping of the hook and what was there said is peculiarly applicable to the present case: "None of them (the workmen) ever complained of it as inadequate and, as we must infer, none of them believed it to be so. They were just as capable to judge of its safety and adequacy as the defendants, and certainly would not have exposed their lives without some protest if they had supposed there was any danger from the use of the hook. No person was called as a witness who ever heard any complaint or allegation anywhere before this accident that the hook was an unsafe or insufficient implement. Under such circumstances can the defendants be charged with negligence? Were they bound to know more than every one else? Ought they to have perceived danger that was not visible to any one else, and which those whose lives were most exposed were not sufficiently wise or vigilant to foresee?"

The defendant in cross-examining plaintiff's witnesses proved that after the accident this bail was taken to defendant's blacksmith shop and that both hooks were straightened, a fact which the plaintiff would not have been permitted to prove. This fact, however, although it doubtless influenced the jury, has no legitimate bearing on the case. The question of defendant's negligence must be judged with reference to the standpoint of the parties at the time of the accident and not in the light of knowledge which almost always comes with the happening of an accident. (See Corcoran v. Village of Peekskill, 108 N.Y. 151; Burke v. Witherbee, supra, 568.)

For the reason, therefore, that the evidence is insufficient to establish the negligence of the defendant the judgment and order must be reversed and a new trial granted, with costs to the appellant to abide the event.

All concurred.

Judgment and order reversed and new trial granted, with costs to appellant to abide event.


Summaries of

Wren v. Kennedy Valve Manufacturing Co.

Appellate Division of the Supreme Court of New York, Third Department
Nov 13, 1907
122 App. Div. 289 (N.Y. App. Div. 1907)
Case details for

Wren v. Kennedy Valve Manufacturing Co.

Case Details

Full title:MARGARET PURTEL WREN, as Administratrix, etc., of THOMAS WREN, Deceased…

Court:Appellate Division of the Supreme Court of New York, Third Department

Date published: Nov 13, 1907

Citations

122 App. Div. 289 (N.Y. App. Div. 1907)
106 N.Y.S. 710

Citing Cases

Schultz v. Barber Asphalt Paving Co.

This class of evidence has been repeatedly condemned by the courts, and was so prejudicial of itself as to…