Opinion
November 16, 1998
Appeal from the Supreme Court, Queens County (Kitzes, J.).
Ordered that the judgment is affirmed, with one bill of costs.
The plaintiff was injured when a load of lumber fell on his hand as he operated a forklift manufactured by the appellant Hyster Company (hereinafter Hyster) and sold by the defendant Modern Handling Equipment of New York, Inc. (hereinafter Modern). The plaintiff commenced the instant action to recover damages for personal injuries on the ground that the forklift was improperly designed, and based on breach of warranty. After trial on the issue of liability, the jury found: that there was a design defect in the forklift; that the defect was a substantial factor in causing the injury; that Hyster did not breach its warranty; that Modern was not negligent; and that the plaintiff was negligent in failing to exercise reasonable care and misusing the forklift. The jury also found that the defendant Hyster was 10% at fault in the happening of the accident, Modern was 0% at fault, the plaintiff was 30% at fault, and the third-party defendant, U.S. Lumber Supply Corp., the plaintiff's employer, was 60% at fault. The trial court, inter alia, granted the motion of the defendant Hyster to set aside the jury verdict, explaining that the plaintiff had not shown proximate cause and therefore had failed to establish a prima facie case.
The courts may set aside a jury verdict upon a finding that the jury could not have reached its verdict on any fair interpretation of the evidence ( see, Nicastro v. Park, 113 A.D.2d 129, 133). Here, the plaintiff failed to show any causal connection between his injury and the allegedly defective design of the retaining pin in the forklift. The plaintiff admitted that he did not use either a retaining pin or a carriage bolt to lock the forks into place, even though he knew that without such a safety mechanism, the forks could and did move. Because he did not use the safety mechanism that came with the forklift, its purportedly defective design could not have caused the plaintiff's accident ( see, Denny v. Ford Motor Co., 87 N.Y.2d 248; Voss v. Black Decker Mfg. Co., 59 N.Y.2d 102).
The plaintiff contends that because the retaining pin is removable, it was foreseeable that the forklift would be operated without it. However, the forklift was not purposefully manufactured to allow its use without the retaining pin, rather the pin was removable in order to be able to adjust the forks ( see, Lopez v. Precision Papers, 67 N.Y.2d 871; Mackney v. Ford Motor Co., 251 A.D.2d 298; Ayala v. V O Press Co., 126 A.D.2d 229).
Moreover, the trial court did not err in precluding the plaintiff's expert witness from testifying as to proximate cause because, in this instance, that connection did not require expert testimony but an understanding of the facts surrounding the accident ( see, Matott v. Ward, 48 N.Y.2d 455).
In light of our determination, we need not address the plaintiff's remaining contentions.
O'Brien, J. P., Joy and Friedmann, JJ., concur.
The plaintiff was injured when a load of lumber fell on his hand as he operated a forklift manufactured by the defendant Hyster Company (hereinafter Hyster). After trial on the issue of liability, the jury found Hyster to be 10% at fault in the happening of the accident as a result of a design defect in the retaining pin of the forklift. The trial court set aside the jury verdict, holding that the plaintiff failed to establish that the design of the forklift was "in any manner improper or unreasonable".
Evidence was adduced at the trial that the retaining pin was defectively designed in that it would easily fall out, pop out, break, or be misplaced, allowing the blades of the forklift to slip. At the time of the accident, the plaintiff's employer had no replacement retaining pins on hand, and used carriage bolts instead. However, the carriage bolts would "pop out and they would either bend and [sic] jam up the fork".
According to the plaintiff's expert, it would have been entirely feasible to mount the pin integral to the machine so that it could not come out, be dropped, pop out, loosen, or get lost.
Evidence that the design of a product is not reasonably safe, and that it was feasible to design it in a safer manner, is sufficient to establish a design defect ( see, Voss v. Black Decker Mfg. Co., 59 N.Y.2d 102, 107; cf., Banks v. Makita, U.S.A., 226 A.D.2d 659). The question of whether, under all of the circumstances, a product is reasonably safe is generally a jury question ( see, Voss v. Black Decker Mfg. Co., supra, at 110).
Hyster contends that the alleged design defect was not a proximate cause of the plaintiff's injuries based upon testimony that the plaintiff used the forklift without the retaining pin, with knowledge of the potential danger that the blades would slip. The majority concurs with that argument, holding that since the plaintiff used the forklift without this safety feature, the defect in its design could not have constituted a proximate cause of the accident.
As the majority notes, a manufacturer generally cannot be held liable if a third party intentionally bypasses a safety feature ( see, Amatulli v. Delhi Constr. Corp., 77 N.Y.2d 525, 533; Neri v. John Deere Co., 211 A.D.2d 915), unless the product is purposefully manufactured to permit its use without the safety feature ( see, e.g., Lopez v. Precision Papers, 67 N.Y.2d 871). Substantial modification of a product by a third party after it leaves the manufacturer's hands to consciously bypass a built-in safety feature forecloses a finding of liability against the manufacturer, because the substantial modification constitutes a superseding cause of the accident ( see, Amatulli v. Delhi Constr. Corp., supra; Robinson v. Reed-Prentice Div., 49 N.Y.2d 471). In the instant case, Hyster argues that the decision not to replace the retaining pin was a substantial modification. In this case there is no evidence that the safety feature was bypassed or defeated by a "substantial material alteration" ( Mackney v. Ford Motor Co., 251 A.D.2d 298, 299, supra). The evidence indicated that the safety device failed because of a design defect attributable to Hyster. The evidence does not indicate that the plaintiff or his employer did anything to bypass any safety devices.
The fact that a safety device broke prior to the accident and thus was not present at the time of the accident owing to a design defect is a valid theory of liability ( see, Liquori v. Hollymatic Corp., 230 A.D.2d 893; Hart v. Hytrol Conveyor Co., 823 F. Supp. 87 [ND NY]). The plaintiff and his employer were negligent in failing to take steps to rectify the problem, but the problem was created by Hyster. Their failure properly goes to the issue of comparative fault, but does not foreclose a finding of liability against Hyster ( see, Voss v. Black Decker Mfg. Co., supra, at 110, n; see, Ramirez v. Sears, Roebuck Co., 236 A.D.2d 530). Their nonfeasance constitutes a concurrent, rather than superseding or intervening cause of the accident ( see, Martinez v. Gouverneur Gardens Hous. Corp., 184 A.D.2d 264).
Based upon this evidence, the jury apportioned 90% of the fault in the happening of the accident to the plaintiff and his employer, and 10% of the fault in the happening of the accident to Hyster. It cannot be said that the apportionment of 10% of the fault in the happening of the accident to Hyster is not supported by the weight of the credible evidence ( see, Martinez v. Gouverneur Gardens Hous. Corp., supra).
The plaintiff's remaining contentions are without merit.